How to install a fridge water line
How to Install a Refrigerator Water Line | hnusta.info
A refrigerator water line is essential to any model that has an ice maker, water dispenser, or both. This water line is connected to the rear of the refrigerator from a cold-water supply line. Whether you're replacing a broken one or putting a new one in, installing a water line is an easy project that requires only a few tools and . Refrigerators with automatic ice makers are a great convenience, especially on a hot day. However, there is nothing automatic about getting a water line hooked up to the ice maker. If you are lucky, there will be a hookup in your kitchen wall near the refrigerator. If not, you will need to run a line to the nearest cold water pipe. Imagine the convenience of having cold water or ice cubes any time you want them -- no more filling up pitchers to keep in the refrigerator or waiting for ice cube trays to freeze. But once you've bought a refrigerator with a cold water dispenser and automatic ice maker, you'll still need a way to get water into it. It takes.
Refrigerators with automatic ice makers are a great convenience, especially on a hot day. However, there is nothing automatic about getting a water line hooked up to the ice maker.
How to Hook Up a Water Line to a Refrigerator
If you are lucky, there will be a hookup in your kitchen wall near the refrigerator. If not, you will need to run a line to the nearest cold water pipe, which is probably in the floor below your kitchen. An hour project of drilling and running flexible hose is well worth the pleasure of ice on demand. Select the location for the valve on your water line.
The folks at GE Appliances recommend using a vertical pipe, if available.
If you must use a horizontal pipe, place the hole for the valve either on the top or side of the pipe. Avoid using the bottom of the pipe, as this may draw sediment into the ice maker.
Take caution to not allow water to seep into your drill and make sure to only pierce one side of the pipe. Attach the valve to the pipe using two pipe clamps. Tighten the screws on the clamps until the sealing washer swells.
Avoid over-tightening; you can crush the copper pipe if you apply too much pressure. Route the tubing to the refrigerator.
Be sure to cut the end of the tubing square. To straighten coiled tubing not the entire rollhave a partner hold the end of the tube flat on the floor, then push the roll against the floor while unrolling to the length you need to go through the cabinets. Connect the Water Line Installation Kit.
Store an additional 8 feet of tubing behind the refrigerator. This extra tubing will allow you to move the refrigerator away from the wall for cleaning and servicing link disconnecting the water supply.
Slide the compression nut and ferrule onto the tubing. Connect the tubing to the valve by hand, then turn one extra time with a wrench.
Turn the water on to flush the tube into a pail for at least 1 quart or until the water runs clear. Shut off water at the new valve. Connect the ferrule and pressure nut to the hose at the refrigerator end.
How to Install a Water Line for a Refrigerator
Attach the nut to the refrigerator valve. If applicable to your refrigerator, run the tubing through the hose clamp to hold it at the preferred angle. Plug in the refrigerator.
Saddle valves are definitely inferior, but they do make it very easy to install fridge water lines without cutting and soldering pipes. Drill holes in source base cabinet walls to route the water line from beneath the sink to the rear of the refrigerator. Take caution to not allow water to seep into your drill and make sure to only pierce one side of the pipe. Connect the household water line to the assembled compression fitting. Harsch received her Certified Nurses Assistant license in
Set the ice maker to the "on" position as indicated in your specific model. Discard the first two or three batches of ice to flush the system. Thomas Ferraioli began writing in His work has been featured in national publications like "Parents" and "U.
Skip to main content. Tighten nuts if leaks occur. Warnings Make sure your refrigerator is disconnected before attaching the water supply line. Consult local plumbing codes to be sure what you do is permitted; for instance, saddle valves are not allowed by Massachusetts building codes.
Resources 1 Ask The Builder: Installing Automatic Ice Maker.
About the Author Thomas Ferraioli began writing in